Channel Professional Powered

Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM

Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM
Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM
Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM
Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM
Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM
Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM
Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM
Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM
Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM
Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM

Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM

Biema Q400 Professional Power Amplifier (new in box). These are 115V made for USA market. The amplifiers are very heavy at almost 50 lbs each and works well to power my subwoofers in my home theater setup (photos are of my own amp). Below are descriptions found online regarding the Biema Q400. Please refer to the detailed specifications below.

The box is 20.3" x 20" x 6.6 and total weight is 47 lbs. The Amplifiers are sealed in original boxes and have not been opened. The Q series amplifiers are designed to be installed in the most demanding of commercial audio applications such as pub PAs, nightclubs, mobile DJs, cinemas and sporting venues. They are uniquely contemporary in appearance and offer high fidelity performance as individual stand alone amplifiers or stereo amplifiers. Each channel is powered by an independent power supply with high efficiency toroidal transformer.

They can be configured to operate in bridge mode (mono) providing up to a massive 1050W RMS power to an 8 ohm load (A4170). They will provide full rated power at less than 0.1% total harmonic distortion. The design incorporates a thermally cued fan forced cooling system. The protection circuitry employed in the design ensures the integrity of the amplifiers under overload conditions.

The circuit even protects itself when a total short circuit is applied across the output terminals. The soft start limiter will immediately shut down the output drive in overload or short circuit conditions, then will gradually restart when the fault condition has been removed. Each channel includes its own recessed front mounted volume control and rear panel mounted XLR & 6.35mm phono jack balanced inputs with selectable sensitivities of 0.77V, 1.4V and 3.5V. This allows input signals from a wide variety of source equipment. Output connections are made via heavy duty binding posts or industry standard heavy duty speaker connectors.

Features: Rugged heavy duty construction 19" rack mount Stylish cosmetics 3 modes of operation - stereo, parallel and bridged Selectable input sensitivity Independent power supplies for each channel Soft start limiter Earth lift switch Limiter on/off switch XLR & 6.35mm balanced inputs Binding post & industry standard heavy duty output speaker connectors Front & rear carry handles Clipping & overload/overdrive protect indicators Recessed detent volume controls for each channel Thermally cued fan forced cooling Specifications: Output power 8 : 2x400W RMS Output power 4 : 2x600W RMS Output power bridged 8 : 1050W RMS Frequency Response: 10Hz - 50KHz -1.5db Imput Sensitivity: 0.77, 1.4, 3.5V Signal to Noise Ration: >100dB Dimensions(WxDxH): 482x390x88 Weight: 20.5kg Features: Rugged heavy duty construction 19" rack mount Stylish cosmetics 3 modes of operation - stereo, parallel and bridged Selectable input sensitivity Independent power supplies for each channel Soft start limiter Earth lift switch Limiter on/off switch XLR & 6.35mm balanced inputs Binding post & industry standard heavy duty output speaker connectors Front & rear carry handles Clipping & overload/overdrive protect indicators Recessed detent volume controls for each channel Thermally cued fan forced cooling Specifications: Output power 8 : 2x400W RMS Output power 4 : 2x600W RMS Output power bridged 8 : 1050W RMS Frequency Response: 10Hz - 50KHz -1.5db Imput Sensitivity: 0.77, 1.4, 3.5V Signal to Noise Ration: >100dB Dimensions (WxDxH): 482mmx390mmx88mm Weight: 20.5kg. The item "Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM" is in sale since Thursday, August 10, 2017. This item is in the category "Consumer Electronics\TV, Video & Home Audio\Home Audio\Home Audio Components\Other Home Stereo Components". The seller is "musclecar-addict" and is located in Millbrae, California. This item can be shipped to United States.
  • Brand: Biema
  • Compatible Brand: For Dynaudio
  • Type: Audio Amplifier
  • Model: Q400
  • Compatible Model: 2x600W
  • Bundle Listing: No
  • Country/Region of Manufacture: China

Biema Q400 Professional Dual Channels Power Amplifier 2x600With4 OHM, 2x400With8 OHM